Shopping Cart

0 item(s) in cart/ total: $0    view cart
Ruger Number One Scope Mount - Slip Over Weaver Style
Ruger Number One Scope Mount - Slip Over Weaver Style

Ruger Number One Scope Mount - Slip Over Weaver Style

Your Price:$59.00
IN STOCK

Part Number:127-816

Slip-Over Scope Mount for Ruger #1
Weaver Style Scope Base Slips Over Ruger No. 1 Rib
  Our new "Slip-Over" Ruger #1 scope mount solves the problem of aligning an after market scope base on a contoured barrel... It uses the factory pre-aligned rib as an alignment shim! Now you can have a precisely aligned Weaver style scope base on your Ruger Number One! Note: This will not work on Ruger No. 1 models with the 2 pc. scope base.
  Installation is Easy - Remove the screws from the original rib. It will stay in place with the recoil pins. Slip the Slip-Over Mount onto the rib. Install our replacement Allen head screws.   Getting an aftermarket scope mount to align properly when mounted on a contour barrel has always been a challenge. Every one of them is a potential hand fitting job... But not with the Slip-Over #1 Mount! The machining is precise. The craftsmanship and finish are exceptional. And, the design is ingenious. Order Your Ruger #1 Slip Over Mount Today.
  Be sure to visit our Ruger No. 1 Home Page!

5 Stars
retired
The mount was VERY easy to install. It holds the scope rings just right. I haven't shot the gun yet; it's a Ruger #1 in .300 Win. Mag. There's more to do on the rifle before it will be fired.
Reviewed by:  from Branford, CT. on 4/13/2017
5/5
5 Stars
none
Best darn mount for Ruger 1 I've seen. Just slip it over and screw it down.
Reviewed by:  from Ohio. on 3/24/2017
5/5
5 Stars
Boar Hunter
Mounted this on Ruger #1 in 375 H&H. It went on easy and fit perfect. Mounted an Aimpoint SC9000 . Have 50 rounds through the rifle and the mount is rock solid. As a side note this Ruger did not have any recoil pins; however, the mount had no problems.
Reviewed by:  from Alvin, Tx. on 1/19/2017
5/5
5 Stars
Mr.
The factory Ruger scope rings on my Ruger #1 just wouldn't allow my Leupold scope tube to mount far enough to the rear for proper eye relief. This slip over Weaver style scope mount allows Weaver style scope rings to be moved much further back, thus enabling proper eye relief for the scope. The answer to scope eye relief problems.
Reviewed by:  from EDMOND, OK. on 10/20/2016
5/5
5 Stars
Customer
This item is very well made and worth every penny. Was my answer for mounting a Redfield 3200 target scope without expensive drilling etc. Would highly recommend.
Reviewed by:  from central Va. on 9/22/2015
5/5
5 Stars
Weaver style slip over rail mount for Ruger #1
Well made. Perfect fit . Allows for greater range of scope mounting , but high rings are needed even for a 42 mm bell to bring a shorter body scope back into eye relief range.
Reviewed by:  from Loganton , Pa. on 9/5/2015
5/5
5 Stars
Mounts
I have mounted your Ruger #1 scope mount on 3 Ruger #1s. Two with Shepherd scopes and I needed to chop off the front of the mount and file concave reliefs for enough clearance to move the scopes back to where I wanted them and re-anodized the ends. Worked perfect. The third was installed on my 45-70 Ruger #1 and it allowed enough forward mount to install a scout EER scope. I am very impressed with the quality and workmanship of your scope mounts.
Reviewed by:  from Washington. on 7/30/2015
5/5
5 Stars
Customer
Installation would have been a piece of cake, but for the original screws on the rifle. I have a lot more respect for the original Ruger #1 than I had before, but the rail certainly adds to the package. I switch scopes around a bit, and this certainly gives one some options. If I had other #1's they would all get this addition.
Reviewed by:  from Spokane. on 6/22/2015
5/5

Recently Viewed Items